Multiscale single Rogowski coil converter RPS50
RPS50 is a multiscale Rogowski coil integrator, in a compact DIN rail enclosure, powered directly from the mains.
An integrator is essential to equalize and shift by 90° the output signal from the Rogowski coils. It consists of an active electronic circuit with negligible offset and a good linearity. RPS50 can be combined with any model and size of MFC150 Rogowski coils. The module is available in the standard configuration with one of the 3 following full scales:
0.5 – 2.5 – 10 kA or 2.5 – 10 – 50 kA or 10 – 50 – 250 kA.
Two different outputs are available.
RPS50 and a Rogowski current transducer is a very flexible system, suitable for high power load analysis, impulsive current monitoring, DC ripple measurement, etc.
Rated voltage: 80…250 VAC 50/60 Hz
Consumption: 1.5 VA max
Electrical characteristics
Input: 1 for Rogowski coil
Input level (RMS) (1): 100mV/1kA@50Hz (only if purchased without MFC150 coil)
Output 1: 1 VRMS (max crest factor 4.5)
3 VRMS (max crest factor 1.5)
Output 1 load: › 10 kOhm
Output 2: 0…10 VDC (on request: 0…20 mA, 4…20 mA)
Full scales values: 0.5 – 2.5 – 10 kA
2.5 – 10 – 50 kA
10 – 50 – 250 kA
Accuracy (2): better than ±1% of full scale (not guaranteed for full scale ≤10 mV)
Frequency range (3): 8 Hz to 100 kHz@-3dB
Environmental conditions
Operating temperature: from -10°C to +50°C
Storage temperature: from -25°C to +70°C
Relative humidity: 80% max without condensation
Mechanical characteristics
Material: plastic enclosure
Protection degree: IP20
Size / weight: 115x100x23 mm / approx 117g
Standards compliance
Safety: 73/23/EEC and 93/68/EEC directives, EN61010.1 safety standard
EMC: 89/366/EEC directive and following modifications
93/31/EEC and 93/68/EEC, EN50081-2, EN50082-2, EN61326/A1
An integrator is essential to equalize and shift by 90° the output signal from the Rogowski coils. It consists of an active electronic circuit with negligible offset and a good linearity. RPS50 can be combined with any model and size of MFC150 Rogowski coils. The module is available in the standard configuration with one of the 3 following full scales:
0.5 – 2.5 – 10 kA or 2.5 – 10 – 50 kA or 10 – 50 – 250 kA.
Two different outputs are available.
RPS50 and a Rogowski current transducer is a very flexible system, suitable for high power load analysis, impulsive current monitoring, DC ripple measurement, etc.
TECHNICAL SPECIFICATIONS
Power supplyRated voltage: 80…250 VAC 50/60 Hz
Consumption: 1.5 VA max
Electrical characteristics
Input: 1 for Rogowski coil
Input level (RMS) (1): 100mV/1kA@50Hz (only if purchased without MFC150 coil)
Output 1: 1 VRMS (max crest factor 4.5)
3 VRMS (max crest factor 1.5)
Output 1 load: › 10 kOhm
Output 2: 0…10 VDC (on request: 0…20 mA, 4…20 mA)
Full scales values: 0.5 – 2.5 – 10 kA
2.5 – 10 – 50 kA
10 – 50 – 250 kA
Accuracy (2): better than ±1% of full scale (not guaranteed for full scale ≤10 mV)
Frequency range (3): 8 Hz to 100 kHz@-3dB
Environmental conditions
Operating temperature: from -10°C to +50°C
Storage temperature: from -25°C to +70°C
Relative humidity: 80% max without condensation
Mechanical characteristics
Material: plastic enclosure
Protection degree: IP20
Size / weight: 115x100x23 mm / approx 117g
Standards compliance
Safety: 73/23/EEC and 93/68/EEC directives, EN61010.1 safety standard
EMC: 89/366/EEC directive and following modifications
93/31/EEC and 93/68/EEC, EN50081-2, EN50082-2, EN61326/A1
