Agilent / Varian Turbo-V 2300 TwisTorr
The Agilent 2000 L/s turbo pump, Turbo-V 2300, offers the highest pumping speeds in its category for Nitrogen (N2). Utilizing leading-edge Twistorr technology, this large turbo pump achieves the highest compression ratios for light gases among commercially available turbomolecular pumps. Due to high foreline pressure tolerance, the pump can be backed by a smaller, cost-effective dry scroll pump like the Agilent TriScroll600.
This large turbo pump is designed for scientific and research applications, where high pumping speed for N2 is important.
The TwisTorr Turbo-V 2300 is operated with a dedicated full display rack controller
Features
Specifications
Technical Specifications
Vacuum Performances
Other
Controller Specifications
This large turbo pump is designed for scientific and research applications, where high pumping speed for N2 is important.
The TwisTorr Turbo-V 2300 is operated with a dedicated full display rack controller
Features
- The Turbo-V 2300 solution comprises a stand-alone pump and rack-type display controller unit
- Advanced rotor design in combination with TwisTorr technology reduces the number of pumping stage
- Our unique monolithic rotor reduces material stress and improves assembly tolerances
- Electrical motor reduces start-up time and improves pump stability under changing gas load conditions
- Higher vacuum performance with lower heat dissipation
- Advanced water cooling system
- Optimized air cooling system
- Clean maintenance-free vacuum
- Utilizes Agilent's A-PLUS software (formerly T-plus)
- Typical Turbo Pump Applications
Specifications
Technical Specifications
Vacuum Performances
Pumping speed for N2 (*) |
N2: 2050 l/s
|
|
|
|
Pumping speed for He (*) | N2: 1800 l/s | |||
Pumping speed for H2 (*) | 1500 l/s | |||
Compression ratio for N2 | > 8 x 108 | |||
Compression ratio for He | 8 x 105 | |||
Compression ratio for H2 | 4 x 104 | |||
Base pressure* (with recommended forepump) | 10-10 mbar (7.5 x 10-11 Torr) (**) | |||
Max foreline pressure for N2 | 4 mbar | |||
Inlet Flange | ISO 250F, CFF 12” O.D. | |||
Foreline flange | KF 40 NW |
Other
Nominal rotational speed |
33300 rpm |
|
|
|
Start-up time without gas load and with the recommended forepump | < 6 minutes | |||
Pumping speed for H2 (*) | 1500 l/s | |||
Minimum recommended forepump | TriScroll 600 | |||
Operational position | Vertical/Upside down | |||
Operating ambient temperature | +5 °C to +35 °C | |||
Bakeout temperature | 120 °C (CFF), 80 °C (ISO) | |||
Max rotor temperature | 120 °C | |||
Vibration level (displacement) | < 0.01 μm at inlet flange | |||
Lubricant | Permanent lubrication | |||
Cooling requirements | Water | |||
Coolant water | Recommended flow: 200 l/h Temperature: +15 °C to +30 °C Pressure: 3 to 5 bar (45 to 75 psi) | |||
Noise level | <60 dB(A) at 1 meter | |||
Storage temperature | -20 °C to +70 °C | |||
Environment protection | IP54 | |||
Weight | ISO 250: 54.2 kg (119.5 lbs) CFF 12”: 55.3 kg (121.9 lbs) |
(*): Without screen
(*): According to standard DIN 28 428, the base pressure is that measured in a leak-free test dome, 48 hours after the completion of test dome bake-out, with a Turbopump fitted with a CFF flange and using the recommended
pre-vacuum pump(*): According to standard DIN 28 428, the base pressure is that measured in a leak-free test dome, 48 hours after the completion of test dome bake-out, with a Turbopump fitted with a CFF flange and using the recommended
Controller Specifications
Input voltages |
100-120 VAC, 220-240 Vac, 1-phase |
|
|
|
Input frequency | 50 - 60 Hz | |||
Maximum input power | 1300 VA | |||
Output voltage | 64 Vac | |||
Output frequency | 555 Hz | |||
Output Power starting | 560 W maximum | |||
Output Power normal | 450 W maximum | |||
Weight (both models) | 12.5 kg (28 lbs) | |||
Installation category | II | |||
Pollution degree | 2 |